Some models of GE refrigerators come with an ice dispenser to make cooling down your drinks more convenient. The touch panel manages the dispenser and will release ice at the user’s command. But what should you do if your GE refrigerator’s ice dispenser isn’t working right? Show
If the ice dispenser in your GE refrigerator won’t work, there’s a problem with the control board or the solenoid. These pieces wear down over time or can become damaged during an electrical failure. Luckily, you can repair a fault ice dispenser at home with a screwdriver. This article will explain why your GE refrigerator’s ice dispenser isn’t functioning correctly and what you can do to fix it. GE Refrigerator Ice Dispenser Not WorkingThe most common reason for a failure in your ice dispenser is a damaged control board. A faulty control board can’t supply the dispenser with sufficient power for it to function. Therefore, replacing the dispenser control board will solve this problem. Follow these steps to service your control board:
In most cases, this will solve the problem. However, replacing the dispenser control board at home could void your warranty, so consult your user manual before attempting this project. An ice dispenser that continuously produces ice has a broken motherboard or a damaged touchpad control. A broken motherboard will also interfere with the other standard functions of your refrigerator. If the ice dispenser is malfunctioning along with other components, call a technician to replace the motherboard for you. On the other hand, if the touchpad control malfunctioned, you can replace this part at home. When the control pad breaks, it can send messages to your ice dispenser to permanently stay on. Use a multimeter to test the control before trying to replace it. Once you’ve found the right replacement piece, use these steps to repair the fountain control:
If this approach is unsuccessful, then the main control board needs repair. Contact a GE technician to test the board and order a replacement, if necessary. Alternatively, you can follow the at-home guide. This approach should restore normal functions to your board once again. Copywrite article owner is Readytodiy.com for this article. This post was first published on 2021-04-24.. GE Refrigerator Ice Dispenser Motor Not WorkingIf the ice dispenser’s motor has broken down, you may need to replace the auger motor or the dispenser actuator to correct the problem. The auger motor is responsible for spinning the blades in your dispenser; thus, the dispenser won’t release ice when this breaks. For older refrigerators, the engine may burn out from usage. However, something as simple as a blackout can also cause your motor to fail. Before calling a repairer, you can test the motor at home to discover if it’s the source of your problem. To check the motor, remove the ice bucket and turn the roller by hand. If the roller spins easily, the final step is to use a multimeter and check its power. If the multimeter shows a lack of continuity, ask a professional to replace the motor. Otherwise, the dispenser actuator is the problem. In either case, you must contact a maintenance specialist to fix this issue. GE Refrigerator Ice Dispenser SlowYour GE ice dispenser will run slowly if:
When your dispenser is working slowly, you don’t need to call a technician. Try these above methods first. GE Refrigerator Ice Dispenser Not Working But Ice Maker IsIf your ice dispenser stops working, but the water is still being released, there may be ice stuck in the chute, or there’s frost on the auger motor. To remove any obstructions stopping the ice, push a stick down the chute from the inside of your refrigerator. This method will release any jammed debris and allow the ice to dispense freely. If this doesn’t work, you have to melt the ice that’s freezing your auger motor. Select the cubed ice option on your dispenser. Afterward, hold the release paddle at the front of your refrigerator for one minute. The dispenser should begin working now. When these fail, schedule a service for your refrigerator immediately. GE Refrigerator Ice Dispenser Flap Not OpeningWhen the ice dispenser’s flap isn’t opening, there’s likely a broken cable in the refrigerator. The wire harness that controls the flap is positioned under the fridge’s bottom or near the top door hinge cover. It’ll be a black wire that leads into the freezer door. Test the wire with a multimeter to confirm whether it works or not. If damaged, replace the wire to restore the flap’s normal functions. GE Refrigerator Ice Dispenser Door Not ClosingAn ice dispenser that doesn’t automatically close its door has a broken solenoid. Replacing the solenoid takes less than an hour and can be done at home using these steps:
How To Fix Ice Dispenser on GE RefrigeratorThe General Electric company provides instructions on how to reset the ice dispenser in most models. For many, a reset is all you need to fix a broken dispenser. Follow these steps:
Afterward, you can turn on your ice maker, and it should function normally. How To Fix Ice Dispenser Door on GE RefrigeratorThe ice dispenser door will break due to corrosion and normal wear and tear. To repair the door, follow these steps:
Related ArticlesGE Refrigerator Freezer Door Won’t Open/Close/Stay Shut GE Refrigerator Freezer Fan Not/Keeps Running/Not Working GE Refrigerator Freezer Problems (Not Cold/Clogged/Stuck) GE Refrigerator Not Working/Cooling After Power Outage ReadyToDiy is the owner of this article. This post was published on 2021-04-24.. Top Reason GE Fridge Is Not Cooling but Freezer Works Why won't my GE refrigerator dispense ice or water?If you discover your GE refrigerator not dispensing water or ice, the dispenser switch may have failed. No voltage, no working dispenser. A multimeter can be used to check for continuity to determine if the dispenser switch is working properly. If there is no continuity, then the switch needs to be replaced.
Why is my ice maker and water dispenser not working?A clog, leak, or damage in the water line may cause the ice maker to shut off automatically or otherwise stop working. Check the ice maker inlet valve and water supply tubing for any leaks, damage, or blockages.
How do you reset a GE refrigerator water dispenser?After you change the water filter, the RESET WATER FILTER button must be pressed and held down for 3 seconds until the red light goes off. On some models the light goes out and on others it will turn green; either is considered normal. If you do not hold the button down firmly, the red light will stay on.
Why is my GE refrigerator ice dispenser not working?Make sure the doors are fully closed. Frozen ice in the bucket can cause only crushed ice to be dispensed or keep ice from dispensing at all. The bucket can be removed and rinsed with warm water. If the condition reappears, the icemaker may be leaking or overfilling which would require service.
|