Having ice ready whenever you want or need it is a luxury we all take for granted, that is, until you reach to get some ice from the freezer and there is none.
Ice makers fail. It's an unfortunate reality of owning a refrigerator with an ice maker.
On the bright side, ice makers are also relatively simple machines that, for the most part, all operate the same way. And you may be able diagnose and repair a faulty ice maker yourself before forking over cash for an expensive service call.
Here's how to fix some common ice maker problems.
When ice is not ejecting
If you find ice inside the ice mold, it means your ice maker is receiving water and the problem likely isn't with the water supply. Instead, it's most likely a mechanical or electrical problem.
Cause: When moving things around in the freezer, it's not uncommon to accidentally nudge the control arm into the off position, which halts production of ice.
Fix: This is an easy fix. Locate the metal control arm and move it to the down or on position.
Cause: If the control arm is in the on (down) position and the mold is filled with ice, the problem likely lies with the motor, gearbox or electrical connection.
Fix: Start by making sure all electrical connections are properly seated. Slide the refrigerator out from the wall, turn off the water supply valve and disconnect it from power. Locate the quick release plug on the back wall inside the freezer. Unplug the connection it and reconnect it to ensure it's fully connected.
Manually remove any remaining ice from the mold by adding some water and letting it sit for a minute. The ice will begin to melt and should be easier to remove.
Restore power to the refrigerator and lift the control arm to the off position. Lower the control arm back down and wait for approximately 10 seconds for the solenoid to engage and fill the mold with water.
Wait three to four hours for the ice to freeze and see if the ice now ejects. If not, it's likely that you will need to replace the motor or gearbox.
When it's not making ice at all
If your ice maker isn't producing ice at all or is producing crescents or cubes that are smaller than usual, it's typically indicative of a clog somewhere along the supply line.
Cause: A common cause for a clog is frozen water in the line.
Fix: To repair a frozen line, slide the refrigerator and unplug it. Locate the shut-off valve, typically underneath the sink or behind the refrigerator. Turn the valve to the closed or off position. Fill a turkey baster with warm water and pour the water over the water line. Alternatively, you can defrost the water line with a hair dryer or by letting the refrigerator sit unplugged for upward of two hours.
Restore power to the refrigerator and listen for the water supply to fill the ice mold.
If the clog is anything but translucent, consult with a professional for help removing the clog.
Cause: There is also a possibility that the water filter for the ice maker is clogged.
Fix: Locate and replace the water filter. Filters for ice makers are typically located inside the refrigerator (to keep them from freezing).
When cubes are too big or small
Cause: If the ice crescents are too big or there is no clog and they're still too small, chances are, the ice maker just needs a little adjustment.
Fix: To adjust how much water the ice mold is filled with each cycle, first remove the cover from the ice maker. It's the white plate on the frontmost part of the ice maker assembly and it should pull off rather easily. If you're having difficulty removing it, use a flat head screwdriver to gently pry it away from the housing.
Under the cover, you should see a screw and spring assembly, along with a plus and minus indicator. This controls the dosing for water. Screw in (toward the minus symbol) to decrease the amount of water per dose and out (toward the plus) to increase the amount of water per dose.
Frigidaire ice maker not working but water does. It is a communal problem that your Frigidaire ice maker stops working, but the water dispenser works.
When it comes to the working of the Frigidaire ice maker, it may sometimes stop to make the ice, but the disposal performs its work side by side, no matter if it is slow or fast.
- Frigidaire ice maker not working but water does
- Switch of a frigidaire ice maker
- Seal of the door of Frigidaire
- Check the freezer temperature
- Water inlet valve
- Replacing of water filter
- Door switch of the Frigidaire
- Water pressure
- Frigidaire ice maker not working Fixed
Let’s discuss the causes along with solutions for the Frigidaire ice maker stop maker:
Switch of a frigidaire ice maker
The switch of the Frigidaire may sometimes get turned off. It may be turned off out of the blue.
If the Frigidaire still doesn’t work, then check the switch again. Check the switch for continuity using an Ohm meter. It needs to replace, change it on an urgent basis.
Seal of the door of
Frigidaire
The temperature of the Frigidaire may get unstable thanks to the fault in the door seal.
The door seal helps to maintain the temperature. If the door seal is not well, then the air may get imbalanced.
To adjust the door at sealing, set the seal as auto. This auto-closing will assist the Frigidaire with maintenance. It comes in rollers or legs.
With these rollers and legs, the fridge gets tilted in different directions. The seal of the Frigidaire will make it defrost, and the ice production will start.
Check the
freezer
temperature
Check the temperature of the freezer, Frigidaire works better at a temperature between 0 and 5 degrees Fahrenheit.
It is imperative to make sure that the condenser coil of the Frigidaire is clean and that the condenser fan is working well.
The condenser fan works to coll down the condenser and compressor. Now, check for the evaporator.
The evaporator coil may produce much frost so the air cannot circulate through the ice maker.
Water inlet valve
The water inlet valve is responsible for the water supply to make ice. This water inlet is an electrically controlled supplier for the dispenser.
When this inlet valve gets defective, or the pressure is not sufficient. Hence the water flow will be stopped. Accordingly, Frigidaire will not make ice.
By and large, the switch and seal of the Frigidaire door are vital for its ice making. Check the faults of the assembly and level control board for proper ice production.
Replacing of water filter
If the Frigidaire ice maker not working, but if the water does, then it may be due to the clogging. Check the water filter if it is clogged, then replace it.
Door switch of the Frigidaire
If you do not want to make your Frigidaire defective, check the switch of the door. The door switch functions by turning it on and off.
When the door is open, it gets turned on the light present in the fridge and it is turned off the ice maker and dispenser.
Water pressure
Another common cause that your Frigidaire ice maker is not working is the low water pressure in the house. Frigidaire comes with a water inlet valve.
This valve makes sure that it supplies water to make ice. It is adapted to work best at a maximum of 20 psi pressure.
Frigidaire ice maker not working Fixed
Related Guides
- Samsung refrigerator noise stops when door open
- How to change water filter in whirlpool french door refrigerator